Champions League

This Article Contents IView:

• 1, Tips for using car navigation
• 2, How to turn on the car navigation
• 3, How to use navigation
• 4, What is a car navigation system?
• 5、What is the working principle of car navigation

Use skills of car navigation

1. First, open the car navigation system and enter the main page, and click "Find The land of". Then enter the destination, as shown in the figure below. Then find the "Set Destination" option and click it to navigate.

2. Get navigation equipment. First of all, you need to get a navigation device, which can be a navigation system installed on the car, a handheld navigation device or a mobile phone navigation software. If you use mobile phone navigation software, you need to install and turn on the GPS positioning function.

3. Open the door on this side of the cab. Step on the brake pedal of the car to prepare to start the engine.Press the one-button start button of the car to start the engine and idle. The instrument of the car lights up, which proves that the whole car has been powered on. Click the switch to start the navigation under the central console of the car.

How to turn on the car navigation

1. Open the door on this side of the car cab. Step on the brake pedal of the car to prepare to start the engine. Press the one-button start button of the car to start the engine and idle. The instrument of the car lights up, which proves that the whole car has been powered on. Click the switch to start the navigation under the central console of the car.

2. First, open the car navigator to enter the main page and click "Find Destination". Then enter the destination, as shown in the figure below.Then find the "Set Destination" option and click it to navigate.

3. Step 1: Open the central control screen of the vehicle and find the icon of the navigation system. Step 2: Click the navigation icon to enter the navigation system menu. Step 3: In the navigation menu, select the "Destination" option. Step 4: Enter the destination address you want to go to, or select the preset location.

4. It is not complicated to use the car navigator. First, start the vehicle, then turn on the car display and on-board navigation function in turn, and finally set up the navigation. Next, let's learn about it with the editor.

5. Preparation before turning on the car navigation. First of all, we need to start the vehicle. Before the vehicle drives, we need to think about where we are going and estimateAbout the time, and start the vehicle, the circuit of the whole vehicle is unobstructed, so that we can operate the navigation system. Turn on the car display.

6. Get navigation equipment. First of all, you need to get a navigation device, which can be a navigation system installed in the car, a handheld navigation device or a mobile phone navigation software. If you use mobile phone navigation software, you need to install and turn on the GPS positioning function.

How to use navigation

Turn on the navigation switch button. After opening, the menu bar button of the initial interface menu will be displayed. Click the "Navigation Bar" button in the menu bar to enter the navigation interface. Determine your location according to GPS (satellite positioning), and now you can search for the destination you need to reach.

The specific method is as follows: First, open the car navigator to enter the main page, and click "Find Destination". Then enter the destination, as shown in the figure below. Then find the "Set Destination" option and click it to navigate.

Open the Gaode map and click the driving option. Enter the starting point and the arrival point. Then click the navigation.

When the navigator is turned on, the car starts to start the navigation. When the device has not found the satellite, the coordinates will stay at the place where the GPS satellite was last obtained. We click to search directly. There are three main ways to input: handwriting, pinyin, and initials. In fact, the first letter is the best.

Tips for using car navigation One trend of electronic products is that the operation is getting easier and easier, and a few buttons can complete the settings you want.However, simple operation does not mean that you can treat it carelessly. A little bit of use and maintenance can greatly extend the life of the navigation.

What is a car navigation system?

1. On-board navigation is carried out using on-board GPS (Global Positioning System) with electronic maps. It can conveniently and accurately tell the driver the shortest or fastest route to the destination, which is a good helper for the driver. Synchronous satellites on Earth were originally used for military and aerial navigation.

2. The vehicle navigation system integrates technologies in automobile, transportation, computer, communication, system science and other fields. The early navigation system mainly used inertial navigation equipment, such as gyros, combses, etc. to locate the direction of the vehicle and estimate the navigation position.Due to its limited use, it has not been widely used.

3. The automotive electronic navigation system is a new technology developed on the basis of the global satellite positioning system (GPS). Its principle GPS is a device that can receive positioning satellite signals, calculate the exact longitude and latitude of the car, as well as the speed and direction of the car through the microprocessor, and display it on the monitor.

4. The vehicle navigation system includes satellite global positioning system (GPS, BeiDou), wireless receiver, various sensors, navigation control unit, map matcher, CD-ROM driver, color liquid display, corresponding software, etc. That monitor is usually in the middle of the dashboard.

5. The GPS navigation system is a radio navigation positioning system that provides drivers with three-dimensional position, three-dimensional speed and other information around the clock through artificial satellites.The GPS navigation system is a radio navigation positioning system that provides drivers with three-dimensional position, three-dimensional speed and other information through artificial satellite around the clock.

6. Car navigation is also known as "car navigation" and "car navigation". It is a kind of navigation device on the car.

What is the working principle of car navigation

The navigator can only display the specific location on the display screen by comparing it with the map in the memory card. The position coordinates determined by the GPS satellite signal will match the electronic map stored in the on-board navigator, so as to determine the exact location of the car in the electronic map, which is commonly known as the positioning function.

Geomagnetic direction sensors, gyroscope sensors, speed sensors, etc. installed on the car are used to determine the trajectory of the car.

The working principle of the car navigation system: through the signal sent by the navigator and the satellite in the sky, it detects the specifics of the car on the earth, and then feeds it back to the navigator, and then shows the specific location on the display by comparing it with the map in the memory card.